Solar concept is not new for us. As non-renewable energy sources are decreasing, usage of solar energy is increased. This solar energy is not only used on the Earth but also used in space stations where no electrical power is available.
Here is the simple circuit to charge 12V, 1.3Ah rechargeable Lead-acid battery from the solar panel. This solar charger has current and voltage regulation and also has over voltage cut off facilities. This circuit may also be used to charge any battery at constant voltage because output voltage is adjustable.
Specifications of the Charging Circuit
Solar panel rating – 5W /17V
Output Voltage –Variable (5V – 14V).
Maximum output current – 0.29 Amps.
Drop out voltage- 2- 2.75V.
Voltage regulation: +/- 100mV
Solar Battery Charger Circuit Principle:
Solar battery charger operated on the principle that the charge control circuit will produce the constant voltage. The charging current passes to LM317 voltage regulator through the diode D1. The output voltage and current are regulated by adjusting the adjust pin of LM317 voltage regulator. Battery is charged using the same current.
Solar panel – 17V
LM317 voltage regulator
Diode – 1n4007
Capacitor – 0.1uF
Schottky diode – 3A, 50V
Resistors – 220, 680 ohms
Pot – 2K
Solar Battery Charger Circuit Design
Circuit must have adjustable voltage regulator , so Variable voltage regulator LM317 is selected. Here LM317 can produce a voltage from 1.25 to 37 volts maximum and maximum current of 1.5 Amps.
Adjustable Voltage regulator has typical voltage drop of 2 V-2.5V .So Solar panel is selected such that it has more voltage than the load. Here I am selecting 17v/5w solar panel.
Lead acid battery which is used here has specification of 12v/1.3Ah. In order to charge this battery following are required.
Schottky diode is used to protect the LM317 and panel from reverse voltage generated by the battery when it is not charging. Any 3 A diode can be used here.
For Charging 12V Battery
Set the output voltage to 14.5 volts(This voltage is specified on the battery as cycle use.)
Charging current = Solar panel wattage/Solar Panel Voltage = 5 / 17 = 0.29A.
Here LM317 can provide current upto 1.5A .So it is recommended to use high wattage panels if more current is required for your application.(But here my battery requires initial current less than 0.39Amps. This initial current is also mentioned on the battery).
If the battery requires initial current more than 1.5A,it is not recommended to use LM317.
Time taken for charging
Time taken for charging = 1.3Ah/0.29A = 4.44hours.
Here solar panel has 5Watts
Power going into battery = 14.5*0.29 =4 watts
Thus 1 watt of power going into regulator.
All the above mentioned parameters have to be taken into account before charging a battery.
For 6V Application
Set the output voltage to 7.5-8 volts as specified on the battery.
calculate the charging current ,power dissipation as shown above.
In this project, power is limited because of the thermal resistance of LM317 voltage regulator and the heat sink. To keep the temperature below 125 degree Celsius, the power must be limited to 10W. LM317 voltage regulator internally has temperature limiting circuit so that if it gets too hot, it shuts down automatically.
When battery is charging, heat sink becomes warm. When completing the charging at maximum voltage, heat sink runs hot. This heat is because of excess power that not needed in the process of charging a battery.
As the solar panel provides constant current, it acts as a current limiter. Therefore the circuit does not need any current limiting.
Solar Charger Protection:
In this circuit, capacitor C1 protects from the static discharge. Diode D1 protects from the reverse polarity. And voltage regulator IC provides voltage and current regulation.
Solar Charger Specifications:
Solar panel rating: 20W (12V) or 10W (6V)
Vout range: 5 to 14V
Maximum power dissipation: 10W (includes power dissipation of schottky diode)
Typical drop out value: 2 to 2.75V (depends on load current)
Max current: 1.5A (internally it limited to 2.2A)
Voltage regulation: +/- 100mV
How to Operate this Solar Battery Charger Circuit?
Give the connections according to the circuit diagram.
Place the solar panel in sunlight.
Now set the output voltage by adjusting pot RV1
Check the battery voltage using digital multi meter.
Solar Battery Charger Circuit Advantages:
Adjustable output voltage
Circuit is simple and inexpensive.
Circuit uses commonly available components.
Zero battery discharge when no sunlight on the solar panel.
Solar Battery Charger Circuit Applications:
This circuit is used to charge Lead-Acid or Ni-Cd batteries using solar energy.